D24T.com  

Go Back   D24T.com > Technical Discussion Area > Help! My car died!
Register FAQ Community Calendar Today's Posts Search

Reply
 
Thread Tools Display Modes
  #1  
Old 05-14-2023, 10:23 AM
barkster1971 barkster1971 is offline
Member
 
Join Date: May 2019
Location: Swineshead
Vehicle: 760gle turbo diesel
Posts: 33
Default head gasket fubared?

Hi,
I feel i might already know the answer but... On starting I'm getting A LOT of white smoke from the exhaust and so much soot is coming out of the exhaust it's leaving a 2 foot black skid mark on my drive.
It's driving ok and doesn't feel lethargic. I've added an NPR intercooler and 240 inlet manifold to my 1984 td 760.
I guess it's on the original crappy head gasket as it's only done 87k.
Cheers, Carl.
Reply With Quote
  #2  
Old 05-14-2023, 09:04 PM
v8volvo v8volvo is offline
Supporting Member
 
Join Date: Jun 2009
Location: Montana, USA
Vehicle: '86 745, '83 764
Posts: 1,655
Default

Are you having to add coolant due to it disappearing, or dealing with any kind of engine overheating, external coolant leaks, or evidence of oil entering the cooling system?

Those would be the signs of headgasket failure. White smoke on a diesel engine, especially at cold start up, is much more likely to be a sign of incorrect engine timing or other combusion issue. But NOT a headgasket problem.

On a gas engine it is true that white smoke (steam) is the telltale for headgasket failure, but diesels more often show white smoke due to misadjustment. White smoke is the result of incomplete combusion of the fuel or combustion at the wrong temperature. Typically means the timing belt was last replaced by someone who did not have the correct equipment and/or did not understand the correct procedures or why they (and the tools) are necessary. It can also occur due to other reasons such as worn fuel injectors, a few dead glow plugs, or poor engine compression though I doubt that is likely in your case.

Contrary to what you may have heard, the original head gaskets are not "crappy" by any stretch. The can of course fail if the engine is overheated due to a burst hose, etc, or if incorrect timing settings and/or excessive modifications (too much boost/fuel) cause excess cylinder pressures far beyond design spec. But on vehicles that have had normal maintenance of the cooling system and are operated under reasonable conditions and expectations the head gaskets can last many hundreds of thousands of miles no issue. There is at least one known D24 that covered one million miles in hard taxicab use that never had the head off the whole time.

So ----- the good news is, it's much easier to correct the engine timing or replace a few glow plugs than replace a head gasket, and unless you are seeing cooling trouble the headgasket is almost certainly just fine and will STAY that way unless you burn up the motor or do something else to injure it.

It sounds like you have started down the path of doing some nice modifications. A bigger intercooler is always a good improvement for both power and engine health. And if you say it drives well and feels peppy, that is a good sign of a healthy engine too. BUT still, most of us here always like to recommend a good "STAGE 0" process before beginning any modifications. That means a full maintenance checkup of things like belts, hoses, cooling system, thermostat, radiator condition, all fluids, a check of the cold starting assist systems (glow plugs and timing advance system), and of course a full timing belt service, done correctly with all factory tools and procedures, unless you have rock solid evidence/paperwork documenting that this was done, correctly, within the last 7 years or 60k miles. That Stage 0 process would likely identify anything causing this white fuel smoke on startup and give you a chance to resolve it.

Check out member ngoma's Hard Starting guide here to get some basics on glow system checkups. Since that is easiest you probably want to start there. Confirm all 6 glow plugs alive and well. https://d24t.com/showthread.php?t=1225

Once that is done, move on to injection timing checks. Then if that is confirmed good, I would look at injector condition and do a compression test (at the same time -- makes sense to do with injectors out). If your engine is original to the 1984 car then it is old enough to have mechanically adjusted valves, thus you should check valve lash as well.

Let us know what you find!
__________________
86 745 D24T/ZF 345k lifted 2.5"
83 764 D24T/M46 155k
Reply With Quote
  #3  
Old 05-15-2023, 10:39 AM
ngoma ngoma is offline
Supporting Member
 
Join Date: Nov 2009
Posts: 1,391
Default

If burning coolant is causing the white smoke, you should be able to smell it (burning coolant--sweet/sharp odor).
__________________
1985 744 gle d24t
1985 745 gle d24t
Reply With Quote
  #4  
Old 05-18-2023, 09:01 AM
v8volvo v8volvo is offline
Supporting Member
 
Join Date: Jun 2009
Location: Montana, USA
Vehicle: '86 745, '83 764
Posts: 1,655
Default

Yes good point, that is also certainly true. That smell coupled with the LOSS of coolant would be a warning sign of headgasket trouble.

But again if the smoke smells like fuel and you don't see any other signs of cooling system problems (coolant loss and/or evidence of sooty color or oil intrusion into coolant) then you can assume it is NOT a headgasket problem.

Also worth noting: if you had an issue with the headgasket causing white smoke (steam) from the exhaust, then you would typically see that white steam all the time, not just after starting the engine. In fact in most cases the steam would be heavier when the engine warmed up.

White smoke only after cold start that disappears as the engine warms up, with no other evidence of cooling system issues, again is typically related to either an issue with the starting aids (glow plugs/cold start timing advance system), improperly adjusted static injection timing, or engine mechanical issue (injectors/valve clearance/compression).
__________________
86 745 D24T/ZF 345k lifted 2.5"
83 764 D24T/M46 155k
Reply With Quote
Reply


Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -8. The time now is 03:31 PM.


Powered by vBulletin® Version 3.8.10
Copyright ©2000 - 2024, vBulletin Solutions, Inc.