|
#1
|
|||
|
|||
Yeah I'll look into electric vacuum pumps and its more than likely a generic one should be capable of doing the job.
Yes, a coolant reservoir off a 960 or late 940 should do that job. I expect it's a relatively simple circuit so you could easily put in an after market bulb or try some with the factory bulbs on the cluster. |
#2
|
|||
|
|||
Hello!
Wrecking yards in the surroundings don’t allow one to come and study… I could also remove the head and go for the 14mm to 16mm rod But this would require extreme precision and doing the head job again and again… There is no mechanics to help me out I’m definitely running out of solution I am going to ditch the car . This is the best thing To be done After all I went through, I managed to get the car run . With a great deal of ordeals ! But it seems I am doomed. If anyone has the contact of sb who could help, I think if I don’t find any solution within a month, I will have to Put an end to this venture |
#3
|
|||
|
|||
Quote:
Do these wrecking yards simply only accept parts orders and they bring it to you at their order desk? Guessing they may be avoiding the risk of injuries (and resultant legal actions) of careless people wandering the yards.
__________________
1985 744 gle d24t 1985 745 gle d24t |
#4
|
|||
|
|||
Quote:
This is a pretty easily solvable problem really. There are LOTS of electric vacuum pump options out there. We can work on this for you and find you a part number to order if that is what will help. Almost every modern turbo gasoline car has an electric vacuum pump to help with brake assist. I have seen them on Volvos, Saabs, Audis, Volkswagens, Subarus.... I am sure there are more. In fact I have a Subaru one sitting on my workbench right now. I would be happy to donate it to you if shipping to Italy can be arranged. The whole process is not complicated. Add the vacuum pump and wire it to run whenever the key is on. Then just remove the vacuum pump pushrod and install the vacuum pump without it. You can also make a blockoff plate but just having the pump sit there dead works equally well, whatever you find to be easier.
__________________
86 745 D24T/ZF 345k lifted 2.5" 83 764 D24T/M46 155k |
#5
|
|||
|
|||
Thank you V8
This message warms my heart … It would be a tremendous help to tell me what set up i should buy ! |
#6
|
|||
|
|||
Here is an example similar to the part I have seen off a Subaru. The one I got came with a VW Jetta TDI that had a failed mechanical vacuum pump and this electric pump was powering the brakes. It worked great!
https://www.ebay.com/itm/31519333530...Bk9SR8q31KPMYw This one is $49 on ebay. I am sure similar pumps exist on ebay in France. (Sorry, I said Italy before, for some reason I had that in my mind as your location. Apologies!) All you have to do is wire it to a sufficient power source that runs whenever the key is on. If it were me, I would probably build a simple circuit using a 4-pole Bosch-type 30A relay with inline fuse direct from the battery, with the relay energized by a wire tapped off the injection pump solenoid which is hot whenever the engine is running. You don't want to overload that circuit to actually power the pump -- hence the use of a relay.
__________________
86 745 D24T/ZF 345k lifted 2.5" 83 764 D24T/M46 155k |
#7
|
|||
|
|||
Thank you very much
If I understand correctly, any 12v vacuum pump would Work without any pb?! |
#8
|
|||
|
|||
Correct!
Any 12V pump that is designed for continuous operation. If it were me I would probably add a vacuum reservoir as well. If you do that, then the pump can be sized smaller since recovery time will not matter as much.
__________________
86 745 D24T/ZF 345k lifted 2.5" 83 764 D24T/M46 155k |
|
|