D24T.com  

Go Back   D24T.com > Technical Discussion Area > Diesel Engine and Drivetrain

Reply
 
Thread Tools Display Modes
  #31  
Old 03-10-2012, 04:21 PM
lmwatbullrun lmwatbullrun is offline
Member
 
Join Date: Jun 2010
Location: eastern USA
Posts: 64
Default looking for an oil pump

Where can I find an oil pump?

I have finally gotten to the point that I am going to pull the motor and replace the gasket, and as long as I have it out I am going to replace the oil pump, if possible.

I also will need an oil pan gasket, which I have not been able to source. Any suggestions on that?
Reply With Quote
  #32  
Old 03-11-2012, 04:03 PM
Volvoist Volvoist is offline
Senior Member
 
Join Date: Nov 2010
Location: Newark/Bear, Delaware
Posts: 189
Send a message via AIM to Volvoist
Default

Quote:
Originally Posted by lmwatbullrun View Post
Where can I find an oil pump?

I have finally gotten to the point that I am going to pull the motor and replace the gasket, and as long as I have it out I am going to replace the oil pump, if possible.

I also will need an oil pan gasket, which I have not been able to source. Any suggestions on that?
To be honest, these pumps are very robust. I doubt it needs to be replaced. New ones are very expensive if you do decide to replace. I would reseal it. I believe the oil pan needs to come off in order to change it as the lower portion shares the pan gasket. Perhaps someone else has done it without pulling the pan though.
__________________
Mike Rausch

Newark/Bear, DE

Selling NEW and USED Volvo parts!

www.swedishbrickyard.com

Email: mike@swedishbrickyard.com
Reply With Quote
  #33  
Old 03-12-2012, 02:09 AM
michaelovitch michaelovitch is offline
Senior Member
 
Join Date: Jun 2011
Location: France
Vehicle: 245 d24 NA
Posts: 179
Default

The oil pan can stay in place i'm 99% sure

but you have to remove the crankshaft, bolt so the timing belt.

That's true it's very strong part.

measure the wear

you can port it if it's off the engine
it will help a bit your efficiency.

__________________
[SIGPIC][/SIGPIC]
Reply With Quote
  #34  
Old 03-13-2012, 06:43 AM
anders anders is offline
Supporting Member
 
Join Date: Jul 2010
Location: NW Washington USA
Posts: 831
Default

You will have to pull the pan as the pickup tube for the oil is bolted to the pump, can't get to those bolts without pulling the pan Pull the engine and do as V8volvo suggested and Paint the block while your at it
__________________
12mm pump heads, ARP stud kits and GTD nozzles available! http://d24t.com/showthread.php?t=1646
NA intake manifolds and 240 turbo pans for sale.
Need d24 or d24t parts? PM me!
Shipments done on fridays!

1982 242 D24+T/M46- Super pumped! Build thread:
http://www.d24t.com/showthread.php?t=1545
1984 764 D24T/ZF build thread: http://www.d24t.com/showthread.php?t=1734
Diesel parts cars: 82 244,83 244, 84 244, 84 245, 85 745
Reply With Quote
  #35  
Old 04-03-2012, 08:43 AM
v8volvo v8volvo is offline
Supporting Member
 
Join Date: Jun 2009
Location: Montana, USA
Vehicle: '86 745, '83 764
Posts: 1,618
Default

Pan gaskets are still pretty easy to find. Any IMC reseller has them (i.e. gowestyautoparts.com). Or you can do as VW now does and use a high quality sealant. Grey Reinzosil is the only thing that I would use. Very thin bead is all that is necessary.

Good luck, you will be glad when you get this one fixed... I know it has been giving you a hard time for quite a while now!
__________________
86 745 D24T/ZF 345k lifted 2.5"
83 764 D24T/M46 155k
Reply With Quote
  #36  
Old 04-03-2012, 08:43 AM
v8volvo v8volvo is offline
Supporting Member
 
Join Date: Jun 2009
Location: Montana, USA
Vehicle: '86 745, '83 764
Posts: 1,618
Default

Pan gaskets are still pretty easy to find. Any IMC reseller has them (i.e. gowestyautoparts.com). Or you can do as VW now does and use a high quality sealant. Grey Reinzosil is the only thing that I would use. Very thin bead is all that is necessary.

Good luck, you will be glad when you get this one fixed... I know it has been giving you a hard time for quite a while now!
__________________
86 745 D24T/ZF 345k lifted 2.5"
83 764 D24T/M46 155k
Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -8. The time now is 06:09 PM.


Powered by vBulletin® Version 3.8.10
Copyright ©2000 - 2024, vBulletin Solutions, Inc.