D24T.com  

Go Back   D24T.com > Technical Discussion Area > Diesel Engine and Drivetrain
Register FAQ Community Calendar Today's Posts Search

Reply
 
Thread Tools Display Modes
  #1  
Old 07-21-2009, 06:23 PM
Slobodan Slobodan is offline
Senior Member
 
Join Date: Jun 2009
Location: Portland, OR
Posts: 214
Send a message via AIM to Slobodan
Default Interesting thing happened this morning

Started fine, drove fine... Then half way to work I am in the top of second and it does this miss thingy.. like it cut out for a second... Very strange.

D24T + IC 3 inch side exit straight through.

What could have happened.
__________________
Redblocks are fun and easy but Greenblocks take skill.
'79 245 with D24TIC + M47
Reply With Quote
  #2  
Old 07-21-2009, 07:01 PM
Jason's Avatar
Jason Jason is offline
Owner/admin
 
Join Date: Jun 2009
Location: St.Louis, MO
Posts: 1,266
Default

Like cut out and dropped a cyl or the whole engine? One cylinder could be a injector problem, possibly a piece of crap in the tip. Whole engine? Look at the injection pump shut down plunger/switch assembly. Could be a loose connection at the terminal, break in the wire or problem at the ignition switch.

Jason
__________________


Back again with a '84 760 GLE D24T/ZF

SOLD but not forgotten! 1984
760 Sedan, built D24Tic/ T-5 swapped

My engine build: http://www.d24t.com/showthread.php?t...t=engine+build
T-5 swap: http://d24t.com/showthread.php?399-W...to-quot-w-pics!
Reply With Quote
  #3  
Old 07-21-2009, 07:18 PM
Slobodan Slobodan is offline
Senior Member
 
Join Date: Jun 2009
Location: Portland, OR
Posts: 214
Send a message via AIM to Slobodan
Default

Seemed like a couple cylinders but definately not the whole engine. Has not done it since.
__________________
Redblocks are fun and easy but Greenblocks take skill.
'79 245 with D24TIC + M47
Reply With Quote
  #4  
Old 07-21-2009, 07:27 PM
Jason's Avatar
Jason Jason is offline
Owner/admin
 
Join Date: Jun 2009
Location: St.Louis, MO
Posts: 1,266
Default

Either injector problem or air in the injection system, in the pump, whatever. Air in the pump getting into the head would cause it to drop a cylinder or two, if the air was pushed down the line instead of fuel.

Jason
__________________


Back again with a '84 760 GLE D24T/ZF

SOLD but not forgotten! 1984
760 Sedan, built D24Tic/ T-5 swapped

My engine build: http://www.d24t.com/showthread.php?t...t=engine+build
T-5 swap: http://d24t.com/showthread.php?399-W...to-quot-w-pics!
Reply With Quote
  #5  
Old 07-26-2009, 09:37 PM
heavyequipment heavyequipment is offline
Junior Member
 
Join Date: Jun 2009
Location: Near Tucson, AZ
Posts: 17
Default

Could be a bad connection at the shutdown solenoid or in that circuit. Hard to find a cause while it's running! Hook up a (small) light to the shutdown solenoid and put the light where you can see it while driving. See if it flickers next time the engine cuts out unexpectedly.
Reply With Quote
  #6  
Old 07-27-2009, 12:53 PM
v8volvo v8volvo is offline
Supporting Member
 
Join Date: Jun 2009
Location: Montana, USA
Vehicle: '86 745, '83 764
Posts: 1,655
Default

Agree with the above... a little air in it, or faulty supply of +12v to pump solenoid. Check the tightness of the female spade connector at the pump. 240 ignition switches are notorious for going bad too... good idea about mounting a test light somewhere where you can see it.
__________________
86 745 D24T/ZF 345k lifted 2.5"
83 764 D24T/M46 155k
Reply With Quote
Reply


Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -8. The time now is 11:00 PM.


Powered by vBulletin® Version 3.8.10
Copyright ©2000 - 2024, vBulletin Solutions, Inc.