D24T.com (http://d24t.com/index.php)
-   Parts for sale (http://d24t.com/forumdisplay.php?f=10)
-   -   12mm "super pump" head/rotor, ARP head studs, GTD nozzles (http://d24t.com/showthread.php?t=1646)

anders 05-23-2016 08:07 PM

12mm "super pump" head/rotor, ARP head studs, GTD nozzles
1 Attachment(s)
I have 6 more of these 12mm "super pump" heads/rotors available to sell. I have been impressed with quality of these parts from this vendor I have purchased fuel system parts for my cummins from them.

$325 for the 12mm pump head/rotor, IP re-seal kit, and input shaft seal shipped to the lower 48. $375 shipped internationally
Want 2 or 3? Additional $300 each

I have fitted 6 of these to our pumps and have been running one for over a 2 years now. I personally know of 4 people local to me running these, all pumps that I built with these 12mm heads.

I also have DNOSD274 "GTD" nozzles and DNOSD297 nozzles from the same manufacturer.
$75 for set of 6.

I'm also selling ARP head stud kits for the D24T, $335 shipped to the lower 48

I will combine shipping.

anders 05-23-2016 08:16 PM

Picture of "superpump" head/rotor
1 Attachment(s)
Here is a picture of the pump heads that are for sale.

anders 06-06-2016 07:40 AM

I have one built pump for sale with the 12mm head and rotor. I have been running it for two months or so on my personal car, $800 with exchange plus shipping.

anders 08-22-2016 06:43 AM

I only have two 12mm head/rotors left.

anders 10-12-2016 07:26 PM

Complete GTD injectors set at 170 bar, $350 set of 6
1 Attachment(s)
I now have Complete injectors for sale, I had the GTD nozzles installed and set at 170 bar. These are NEW and from the same vendor I have been using for my cummins injectors, 12mm pump heads and the nozzles.
Selling for $315 a set shipped to the lower 48 and no core charge!
I will ship these internationally, discounts available on larger purchases also!

Kraftwerk 10-17-2016 11:57 AM

Any actual videos of your cars?

If there are, pardon my ignorance.

anders 10-17-2016 03:27 PM

82 242
Video of the 242 in my signature-

andler 09-26-2017 11:29 AM

Have you ever had the pumps in a bench so you can see how much CC it gives?

Brekizer 09-29-2017 10:59 PM

How much of a performance increase does the 12mm heads in combination with the gtd injectors make?

I think I'm interested.

RedArrow 09-30-2017 06:35 AM

I have the 12mm stuff but not yet installed,
the gtd nozzles (set at 170) are in and it was a huge difference immediately.
Idk why, probably my injectors were very worn out. I am crurious now how it would run on new stock injectors as a comparison.
I am not sure about that ...but now I have about 100miles on the gtds and I have to say it is awesome. The car is peppier, less noise and rattle, much much smoother idle and running, cold starts simply sound amazing And all smoke disappeared too. Pulls much stronger too.
Purposely I havent changed timing or anything (i just put the new injectors in) so I can experiment with the gtds alone.
So far it was a GREAT improvement.

Since then i got the manifolds off and fully cleaned the poop out and added new gaskets for both and it simply runs amazing.

Re: "forum is dead"
Hopefully the forum wakes up as weather cools and temps go down...diesels need more love and maintenance from now on. Lol.
Keep bricking!

All times are GMT -8. The time now is 10:03 AM.

Powered by vBulletin® Version 3.8.10
Copyright ©2000 - 2022, vBulletin Solutions, Inc.