D24T.com  

Go Back   D24T.com > Technical Discussion Area > Performance and aftermarket

Reply
 
Thread Tools Display Modes
  #1  
Old 05-06-2016, 04:13 AM
ian2000t ian2000t is offline
Senior Member
 
Join Date: Feb 2011
Location: West Mids, UK
Posts: 226
Default Best Nozzles?

I've seen lots of talk of different nozzles lately, and I'm wondering which are the best to use? What are the differences/advantages of each?

I think the standards are "193" or "293"?

I currently have the Monarch version of "273" (GTD?). These were smoother, but I can't say they really gave me any extra power.

I've seen a thread recently about "297" nozzles as well:
http://d24t.com/showthread.php?t=1604

And, I swear I read on a Swedish (translated) forum that they run Mercedes nozzles which proved to be a good upgrade - not sure about this though.

So, thoughts:
193
293
273
297
__________________
1990 Volvo 765 D24Tic (factory UK spec Tic). Monark 273 nozzles 163bar, Ajusa MLS gasket, 16psi, Water Injection, 17" Titans with 25mm H&R spacers, running 85% WVO/SVO.
http://i103.photobucket.com/albums/m...AG0269-sig.jpg
Reply With Quote
  #2  
Old 05-06-2016, 10:14 AM
anders anders is offline
Supporting Member
 
Join Date: Jul 2010
Location: NW Washington USA
Posts: 831
Default

There is also 274 and 276 nozzles. I have installed a set of 297's in a 764, it ran cleaner.
As what nozzles are the better performers I'm not sure.
__________________
12mm pump heads, ARP stud kits and GTD nozzles available! http://d24t.com/showthread.php?t=1646
NA intake manifolds and 240 turbo pans for sale.
Need d24 or d24t parts? PM me!
Shipments done on fridays!

1982 242 D24+T/M46- Super pumped! Build thread:
http://www.d24t.com/showthread.php?t=1545
1984 764 D24T/ZF build thread: http://www.d24t.com/showthread.php?t=1734
Diesel parts cars: 82 244,83 244, 84 244, 84 245, 85 745
Reply With Quote
  #3  
Old 05-09-2016, 05:04 AM
ian2000t ian2000t is offline
Senior Member
 
Join Date: Feb 2011
Location: West Mids, UK
Posts: 226
Default

Did you notice any power gains/losses with the 297's?
__________________
1990 Volvo 765 D24Tic (factory UK spec Tic). Monark 273 nozzles 163bar, Ajusa MLS gasket, 16psi, Water Injection, 17" Titans with 25mm H&R spacers, running 85% WVO/SVO.
http://i103.photobucket.com/albums/m...AG0269-sig.jpg
Reply With Quote
  #4  
Old 05-09-2016, 09:28 AM
anders anders is offline
Supporting Member
 
Join Date: Jul 2010
Location: NW Washington USA
Posts: 831
Default

All I know is they can flow some fuel with a 12mm pump.
I wish someone could state for a fact what the difference is in the nozzles. Slightly different needle shapes? Lager orifice?

Here is a picture of a 764 with a 12mm pump I built and the 297 nozzles, it's flowing a bit of fuel..
Attached Images
File Type: jpg image.jpg (20.3 KB, 60 views)
__________________
12mm pump heads, ARP stud kits and GTD nozzles available! http://d24t.com/showthread.php?t=1646
NA intake manifolds and 240 turbo pans for sale.
Need d24 or d24t parts? PM me!
Shipments done on fridays!

1982 242 D24+T/M46- Super pumped! Build thread:
http://www.d24t.com/showthread.php?t=1545
1984 764 D24T/ZF build thread: http://www.d24t.com/showthread.php?t=1734
Diesel parts cars: 82 244,83 244, 84 244, 84 245, 85 745
Reply With Quote
  #5  
Old 05-11-2016, 05:55 AM
ian2000t ian2000t is offline
Senior Member
 
Join Date: Feb 2011
Location: West Mids, UK
Posts: 226
Default

Hmm, interesting. I don't really understand the differences. I do feel my Monark "273" nozzles didn't give me anymore extra power than you would expect rebuilt injectors vs. old injectors to give anyway.

Is is true that running higher pressure will reduce the amount of fuel they flow, as they are open for a shorter period of time?
__________________
1990 Volvo 765 D24Tic (factory UK spec Tic). Monark 273 nozzles 163bar, Ajusa MLS gasket, 16psi, Water Injection, 17" Titans with 25mm H&R spacers, running 85% WVO/SVO.
http://i103.photobucket.com/albums/m...AG0269-sig.jpg
Reply With Quote
  #6  
Old 05-12-2016, 04:41 AM
anders anders is offline
Supporting Member
 
Join Date: Jul 2010
Location: NW Washington USA
Posts: 831
Default

I believe that any of the stock nozzles are more then capable of flowing what a max 10mm head/rotor can put out. As far as higher pop pressures, I could only assume the higher the pop pressure there might be a very slight decrease in fuel injected per stroke of the plunger. As the pressure rises there is more of a chance of the fuel getting pushed past the control collar and the mating surfaces of the plunger and head itself, it would be very minimal though.

The injectors will remain open as long as it's needed to inject the specific quantity of fuel the IP is suppling, whether it be at 130 bar, 155 bar or 180 bar.
__________________
12mm pump heads, ARP stud kits and GTD nozzles available! http://d24t.com/showthread.php?t=1646
NA intake manifolds and 240 turbo pans for sale.
Need d24 or d24t parts? PM me!
Shipments done on fridays!

1982 242 D24+T/M46- Super pumped! Build thread:
http://www.d24t.com/showthread.php?t=1545
1984 764 D24T/ZF build thread: http://www.d24t.com/showthread.php?t=1734
Diesel parts cars: 82 244,83 244, 84 244, 84 245, 85 745
Reply With Quote
  #7  
Old 05-12-2016, 04:56 AM
ian2000t ian2000t is offline
Senior Member
 
Join Date: Feb 2011
Location: West Mids, UK
Posts: 226
Default

OK fair enough, just a thought.

I'm comparing it to my other car - a Rover 45 Turbo Diesel. These have 210 bar injectors and with standard fuel settings put out 100BHP.

Simply switching to the 200 bar earlier injectors running standard fuel settings increases to ~130BHP. Add a remap, and 150bhp is usual.

I understand they are completely different setups though - the Rover being direct injection and using the VP37 electronic pump.
__________________
1990 Volvo 765 D24Tic (factory UK spec Tic). Monark 273 nozzles 163bar, Ajusa MLS gasket, 16psi, Water Injection, 17" Titans with 25mm H&R spacers, running 85% WVO/SVO.
http://i103.photobucket.com/albums/m...AG0269-sig.jpg
Reply With Quote
  #8  
Old 04-24-2017, 05:58 AM
Brekizer Brekizer is offline
Member
 
Join Date: Feb 2017
Location: Fryslân (North of the Netherlands)
Vehicle: Volvo 740 Estate D24t
Posts: 38
Default

Hi,

I'm new here but I've purchased some new GTD nozzles of the German ebay.
My old injectors are quite charred up so I would like to refurbish them with the new nozzles installed.

But how much bar would you guys recommend?
Stock is 150 bar right?

Think 170 bar is a nice middle way or do you guys think its a waste of time?
Reply With Quote
  #9  
Old 04-24-2017, 09:21 AM
anders anders is offline
Supporting Member
 
Join Date: Jul 2010
Location: NW Washington USA
Posts: 831
Default

I get my injectors set at 170 bar, I have yet to run a set though.
__________________
12mm pump heads, ARP stud kits and GTD nozzles available! http://d24t.com/showthread.php?t=1646
NA intake manifolds and 240 turbo pans for sale.
Need d24 or d24t parts? PM me!
Shipments done on fridays!

1982 242 D24+T/M46- Super pumped! Build thread:
http://www.d24t.com/showthread.php?t=1545
1984 764 D24T/ZF build thread: http://www.d24t.com/showthread.php?t=1734
Diesel parts cars: 82 244,83 244, 84 244, 84 245, 85 745
Reply With Quote
  #10  
Old 05-21-2017, 05:28 AM
swital swital is offline
Member
 
Join Date: Nov 2013
Location: Płock
Posts: 31
Default

I must rebuild my injectors and have stock pump. So the 293 are stock nozzles ? The GTD are 273 = monark nozzles ? and which are best ? I heard too about nozzles from bmw tds DN0SD318.
__________________
now: 480S, 480 Collection 158, 744 USA FK+ M90, 744 USA, 245 USA D24T+ +IC, 850 T-5R, 945 FK, 440, 460

ex: 745 USA FT, 480S, 3x480ES, 2xV70I, 945 D24TIC, 440

Last edited by swital; 05-21-2017 at 06:19 AM.
Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -8. The time now is 12:08 PM.


Powered by vBulletin® Version 3.8.10
Copyright ©2000 - 2024, vBulletin Solutions, Inc.