#1
|
|||
|
|||
Nozzle injectors
What do you think about nozzle injectors from BMW 2.5 TDS or all injectors to D24T :?:
__________________
now: 480S, 480 Collection 158, 744 USA FK+ M90, 744 USA, 245 USA D24T+ +IC, 850 T-5R, 945 FK, 440, 460 ex: 745 USA FT, 480S, 3x480ES, 2xV70I, 945 D24TIC, 440 |
#2
|
|||
|
|||
If it isn't broken, fix it until it is.
|
#3
|
|||
|
|||
but the end of the injector of bmw have larger holes, so we have a better injection and combustion.
__________________
now: 480S, 480 Collection 158, 744 USA FK+ M90, 744 USA, 245 USA D24T+ +IC, 850 T-5R, 945 FK, 440, 460 ex: 745 USA FT, 480S, 3x480ES, 2xV70I, 945 D24TIC, 440 |
#4
|
|||
|
|||
My car has a 3" exhaust. I could change it to 4", but it won't be any faster.
We have the correct spray angle, and good atomization. I think you need to change the pump quite a bit before injectors are your bottleneck. |
#5
|
|||
|
|||
I want to 100-110kW, so factory injectors will be good, but pump ?
I heard that the pump is best lodge with two, down from the d24, and the top from d24t
__________________
now: 480S, 480 Collection 158, 744 USA FK+ M90, 744 USA, 245 USA D24T+ +IC, 850 T-5R, 945 FK, 440, 460 ex: 745 USA FT, 480S, 3x480ES, 2xV70I, 945 D24TIC, 440 |
#6
|
|||
|
|||
Quote:
If doing this you would want to check the pop pressure, maybe even advance the injection timing while you're at it.
__________________
Jim 1985 Volvo 740 GLE turbo diesel |
#7
|
|||
|
|||
The GTD injectors offer more needle lift, as well as possibly bigger holes.
The injection pump is a fixed volume per stroke limited by 10mm head size, then that is regulated down be the control collar. Unless those are changed the additional capacity of a larger injector isn't utilized, and I doubt you'd see much gain beyond what comes from them being new. The goal is not much more than a D24TIC which uses the same injector as D24t. I really think with intercooler, free exhaust and some fiddling with fuel screws, you will be there. Some of the 4 banger IDI guys are reaching this level at 25-30 PSI with stock injectors. As far as I am aware there is no advantage to the D24 lower half, and I will definitely chose the turbo top anytime one is available. |
#8
|
|||
|
|||
So how I can get that 100kW or little more, factory injectors and pump ? only mbc and more boost ? of course I must do the fuel pin and maybe increase the dose of fuel. I want do it all on factory turbine.
__________________
now: 480S, 480 Collection 158, 744 USA FK+ M90, 744 USA, 245 USA D24T+ +IC, 850 T-5R, 945 FK, 440, 460 ex: 745 USA FT, 480S, 3x480ES, 2xV70I, 945 D24TIC, 440 |
#9
|
|||
|
|||
Install an EGT gauge, Intercool, exhaust. The stock turbo will be pretty inefficient at the high end of that level, and if your head gasket isn't fresh, it will probably hate you.
|
|
|