D24T.com  

Go Back   D24T.com > Technical Discussion Area > Help! My car died!
Register FAQ Community Calendar Today's Posts Search

Reply
 
Thread Tools Display Modes
  #11  
Old 08-31-2014, 08:07 PM
RedArrow RedArrow is offline
Senior Member
 
Join Date: Jan 2013
Location: New York
Vehicle: 1986 Volvo 745 TD
Posts: 903
Default Part 2

Killing time, fixing/rerouting some wiring, cleaning under hood, fixing-installing the never-worked-before `engine light`, then testing how nicely it works; I look down-->what do I see?
Picture #4. Yes, the rear hose, covered in greasy poo. Ugly?Yes. Dangerous? What?!=yes!! Hose in Bad cond?idk yet.
Searching for reasons, Thinking I`m in need of a new valve cover gasket, etc, checking inj.pump to see any leaks etc, I explored another issue that also helped my d24t getting all that oily crap on it.... Pict #5.
Is that hose still available? How about our rear heater hose?
Thanks for commenting.
Attached Images
File Type: jpg 20140831_170410[1].jpg (81.0 KB, 10 views)
File Type: jpg 20140831_175118[1].jpg (89.0 KB, 10 views)
File Type: jpg 20140831_215950[1].jpg (89.0 KB, 12 views)
File Type: jpg 20140831_220430[1].jpg (97.3 KB, 16 views)
File Type: jpg 20140830_181503[1].jpg (85.9 KB, 15 views)

Last edited by RedArrow; 08-31-2014 at 08:22 PM.
Reply With Quote
  #12  
Old 08-31-2014, 08:40 PM
RedArrow RedArrow is offline
Senior Member
 
Join Date: Jan 2013
Location: New York
Vehicle: 1986 Volvo 745 TD
Posts: 903
Default Lucky me I saw what`s happening.

Quote:
Originally Posted by casioqv View Post
Since this hose goes from the IP to the head, stiffness isn't a concern so you can replace it with stiffer than stock hose or pipe.
Thanks for the advice. I was real lazy to try the dental floss solution, I still like it BUT hopefully I`ll never need it on the road!
While waiting for car to warm up& thermostat to open so I can get air` out (after installing my jerry-built hose junction) , I experienced that the direction of flow of Zerex is towards the ip/coldstart device, of course.
Thank you forumers for all of your ideas. I hope my posting helps other brickers dealing with d24/d24t issues, so we can save many for later generations. ))
My before-and-after trip `hood-opening rituals` saved my @s$ again. And the car. Get out there and check things under hood.I mean, constantly. You have a 20+ y old BRiCK! ))

Last edited by RedArrow; 09-01-2014 at 05:14 AM.
Reply With Quote
  #13  
Old 09-01-2014, 08:18 AM
ngoma ngoma is offline
Supporting Member
 
Join Date: Nov 2009
Posts: 1,388
Default

Quote:
Originally Posted by RedArrow View Post
I know the best would be to ROLL BEAD the tube!!
RIGHT? (creating an edge so hoses wouldn`t have any chance of sliding off)
Good work. Should be OK. Max coolant pressure is 75kPa (less than 11 PSI) if you're using the black expansion tank cap. Retighten the hose clamps when it is hot and you're good to go.
__________________
1985 744 gle d24t
1985 745 gle d24t
Reply With Quote
  #14  
Old 09-01-2014, 08:23 AM
ngoma ngoma is offline
Supporting Member
 
Join Date: Nov 2009
Posts: 1,388
Default

Quote:
Originally Posted by RedArrow View Post
...check things under hood.I mean, constantly. You have a 20+ y old BRiCK! ))
20 years old? I wish! You're off by about 15 years!
__________________
1985 744 gle d24t
1985 745 gle d24t
Reply With Quote
  #15  
Old 09-01-2014, 09:03 AM
RedArrow RedArrow is offline
Senior Member
 
Join Date: Jan 2013
Location: New York
Vehicle: 1986 Volvo 745 TD
Posts: 903
Talking No d24t is `only 20y old` here :(

Quote:
Originally Posted by ngoma View Post
20 years old? I wish! You're off by about 15 years!
Yes, of course you`re absolutely right, but I thought, older ladies always like it when you `SET` their age at a bit lower.
THANKS.Yes, I have the black exp tank cap. I`ll retighten clamps once car gets up to temp. I need to wait for a while as PS pump is loose, belt is off currently...

for the holiday, f@t Santa Claus visited here and he surprised me with a new tb cover. F.ck, he was too fast to leave me a manifold; or maybe i haven`t recently been behaving well.
This stup.d DupliColor engine enamel dries so slowly! I can`t just grab cover (unless wanting to fingerprint it) to install rubber trim/seal/clips/plugs back, not to mention putting cover back on engine... But it does look funky on there. More pictures tomorrow.
Attached Images
File Type: jpg 20140831_182322[1].jpg (84.6 KB, 8 views)
File Type: jpg 20140831_185652[1].jpg (87.9 KB, 6 views)
File Type: jpg 20140831_201019[1].jpg (87.5 KB, 8 views)
File Type: jpg 20140901_110118[1].jpg (87.8 KB, 11 views)

Last edited by RedArrow; 09-01-2014 at 06:17 PM.
Reply With Quote
  #16  
Old 09-05-2014, 07:59 PM
RedArrow RedArrow is offline
Senior Member
 
Join Date: Jan 2013
Location: New York
Vehicle: 1986 Volvo 745 TD
Posts: 903
Default Red

Spray can chased off ps pulley too
Paint`s good match to color code 173-2
Attached Images
File Type: jpg 20140902_182257[1].jpg (87.3 KB, 13 views)
File Type: jpg 20140902_185146[1].jpg (87.7 KB, 11 views)
File Type: jpg 20140901_152014[1].jpg (87.1 KB, 10 views)
File Type: jpg 20140901_151732[1].jpg (80.3 KB, 10 views)
Reply With Quote
  #17  
Old 09-25-2014, 07:14 PM
RedArrow RedArrow is offline
Senior Member
 
Join Date: Jan 2013
Location: New York
Vehicle: 1986 Volvo 745 TD
Posts: 903
Default Breather/vent hose part number

Quote:
Originally Posted by RedArrow View Post
...issue that helped my d24t getting all that oily crap on it.... Pict #4 and #5.
Is that hose still available?
Thanks for commenting.
Talking about hoses again...
the one that runs from valve cover towards turbo... The d24t crankcase vent hose became very brittle, it cracked at both ends. After taking a pict, I got rid of it &installed a heater hose as a temp fix, `cause thanks to this crappy hose: the passenger side of engine always got oily mess on it... from underneath the upper clamp...oil escaped, travelled back by the side of valve cover, then down, reaching near rear belt, rear coolant hose etc, leaving oily residue on&around manifold etc.
I`m trying to find the correct part number so I`ll be able to order it. Any info where to order? THX
ps.
hose was put on plastic joint with metal piece being INSIDE the hose.
See picture #4 & #5 in posting #11.

Last edited by RedArrow; 09-25-2014 at 07:21 PM.
Reply With Quote
  #18  
Old 09-25-2014, 10:01 PM
ngoma ngoma is offline
Supporting Member
 
Join Date: Nov 2009
Posts: 1,388
Default

Volvo P/N 1328650-5

From Volvo 740 parts catalog. 17MB download, but well worth it.

Groep 20 Motor; 25 Inlaatsystem, uitlaat; D24 Luchtfilter, page 215
__________________
1985 744 gle d24t
1985 745 gle d24t
Reply With Quote
  #19  
Old 09-27-2014, 07:05 AM
RedArrow RedArrow is offline
Senior Member
 
Join Date: Jan 2013
Location: New York
Vehicle: 1986 Volvo 745 TD
Posts: 903
Default

Quote:
Originally Posted by ngoma View Post
Volvo P/N 1328650-5

From Volvo 740 parts catalog. ...
Great info, nice find! Thanks a bunch.
Reply With Quote
  #20  
Old 11-01-2014, 12:14 PM
RedArrow RedArrow is offline
Senior Member
 
Join Date: Jan 2013
Location: New York
Vehicle: 1986 Volvo 745 TD
Posts: 903
Default just a quick update

Quote:
Originally Posted by ngoma View Post
Good work. Should be OK. Max coolant pressure is 75kPa (less than 11 PSI) if you're using the black expansion tank cap. Retighten the hose clamps when it is hot and you're good to go.
Yes, I have the black one.

Since the fix I drove over 3000 miles and no issues.

The later mentioned `vent hose` (from valve cover towards turbo) deteriorated a lot, so I used a thick-wall heater hose to replace it, temporarily.
Reply With Quote
Reply


Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -8. The time now is 03:45 PM.


Powered by vBulletin® Version 3.8.10
Copyright ©2000 - 2024, vBulletin Solutions, Inc.