Forum: New Member Introductions
05-21-2019, 11:11 AM
|
Replies: 96
Views: 125,720
I tested and installed six new Meyle plugs,...
I tested and installed six new Meyle plugs, squirted a half teaspoon of oil into the cylinders and installed the injectors with new heat shields. She's still not starting.
I cracked open each...
|
Forum: New Member Introductions
05-13-2019, 11:01 AM
|
Replies: 96
Views: 125,720
|
Forum: New Member Introductions
05-08-2019, 08:46 PM
|
Replies: 96
Views: 125,720
I haven't got much time for the car these days...
I haven't got much time for the car these days because spring is here. I began following your advice and pulled the injectors and shields to add oil to the cylinders. After doing that I turned the...
|
Forum: New Member Introductions
05-02-2019, 06:15 PM
|
Replies: 96
Views: 125,720
We're getting close with smoke. but no cigar. I...
We're getting close with smoke. but no cigar. I put in a new battery, fuel filter and attempted to bleed the system with a Mighty Vac and a primer bulb. All fuel lines are blead except for cylinders...
|
Forum: New Member Introductions
04-26-2019, 03:41 PM
|
Replies: 96
Views: 125,720
So that explains the gap. I temporarily have a...
So that explains the gap. I temporarily have a thick washer in there and plan correct it by installing the joist bracket. I'll check the PS pump bracket to see if that's where that nut and bolt...
|
Forum: New Member Introductions
04-22-2019, 07:09 AM
|
Replies: 96
Views: 125,720
|
Forum: New Member Introductions
04-21-2019, 02:50 PM
|
Replies: 96
Views: 125,720
Thanks for the exhaust info, guys.
At this...
Thanks for the exhaust info, guys.
At this point I have the installed the fuel Ines, radiator and hoses, fan and shroud, and the valve cover.
In the next couple of days I plan to install the...
|
Forum: New Member Introductions
04-14-2019, 06:47 PM
|
Replies: 96
Views: 125,720
Yes, the two triangular pieces. I have the...
Yes, the two triangular pieces. I have the manifold gaskets. When I search online there's only the crushable donut types with nuts, bolts and springs which I've used on other vehicles. There was only...
|
Forum: New Member Introductions
04-14-2019, 07:51 AM
|
Replies: 96
Views: 125,720
|
Forum: New Member Introductions
04-11-2019, 04:53 AM
|
Replies: 96
Views: 125,720
|
Forum: New Member Introductions
04-09-2019, 09:02 PM
|
Replies: 96
Views: 125,720
|
Forum: New Member Introductions
04-08-2019, 09:23 PM
|
Replies: 96
Views: 125,720
|
Forum: New Member Introductions
04-08-2019, 09:14 PM
|
Replies: 96
Views: 125,720
|
Forum: New Member Introductions
04-05-2019, 05:47 PM
|
Replies: 96
Views: 125,720
|
Forum: New Member Introductions
04-05-2019, 03:26 PM
|
Replies: 96
Views: 125,720
|
Forum: New Member Introductions
04-02-2019, 06:47 PM
|
Replies: 96
Views: 125,720
|
Forum: New Member Introductions
03-23-2019, 11:25 AM
|
Replies: 96
Views: 125,720
Thank you, Goteborg Vapenfabrik!! I'll fab that...
Thank you, Goteborg Vapenfabrik!! I'll fab that up next week and torque that bolt properly. Only thing is I may make it for 1/2 inch drive unless I go to Harbor Freight to pick up a 3/4 one. Also,...
|
Forum: New Member Introductions
03-21-2019, 07:32 AM
|
Replies: 96
Views: 125,720
|
Forum: New Member Introductions
03-20-2019, 06:40 PM
|
Replies: 96
Views: 125,720
|
Forum: New Member Introductions
03-20-2019, 02:26 PM
|
Replies: 96
Views: 125,720
I now have the heat shields, injectors, new...
I now have the heat shields, injectors, new timing belt and harmonic balancer installed. The engine block is cleaned up including head bolt holes and mating surface. Now getting ready to install...
|
Forum: New Member Introductions
03-11-2019, 04:27 PM
|
Replies: 96
Views: 125,720
|
Forum: New Member Introductions
03-10-2019, 06:34 PM
|
Replies: 96
Views: 125,720
|
Forum: New Member Introductions
03-10-2019, 07:37 AM
|
Replies: 96
Views: 125,720
Hey guys, I'm back. Sorry for the delay but got...
Hey guys, I'm back. Sorry for the delay but got caught up with other things. My last post was a year ago and at that time I was going to the parts place to pickup the heat shields and filters then...
|
Forum: New Member Introductions
03-08-2018, 06:08 PM
|
Replies: 96
Views: 125,720
|
Forum: New Member Introductions
03-07-2018, 05:45 PM
|
Replies: 96
Views: 125,720
With some more lapping (the old fashioned way),...
With some more lapping (the old fashioned way), the valves are sealing well. The camshaft and seals are installed. Now I'm looking at the injectors. They've been sitting in a stainless bowl, covered...
|