D24T.com

D24T.com (http://d24t.com/index.php)
-   Suspension and Brakes (http://d24t.com/forumdisplay.php?f=5)
-   -   Front susp (http://d24t.com/showthread.php?t=1032)

RedArrow 04-18-2013 06:36 PM

Front susp
 
5 Attachment(s)
Not surprised. Left front has a fresh leak now.
http://www.youtube.com/watch?v=hxrS1...ature=youtu.be
and
http://www.youtube.com/watch?v=_LuLt...ature=youtu.be

RedArrow 05-02-2013 07:24 PM

Strut structure struggle
 
3 Attachment(s)
I could use a great reliable spring compressor. I`ll have to look around in a few stores. Which ones work well? Autozone sells cheapo ones for high bucks...:( I checked the left front of vehicle for loose connections and badly worn bushings but could not find any dangerous thing... except for the monster spring of course:).

745 TurboGreasel 05-03-2013 01:19 PM

The clamshell ones are best, but are like $300
I have a couple sets of W89322 that work fine, and made some adapters to allow driving them from the other end.

ngoma 05-04-2013 10:59 PM

I have this
http://www.harborfreight.com/single-...sor-43753.html

and (similar to) this
http://www.harborfreight.com/macpher...-set-3980.html

They both work. The clamshell style is less bunglesome, and seems more secure.

Tip: grease the threads for longevity.

Last I checked, Autozone had the dual screw type as part of their tool loaner program.

RedArrow 05-05-2013 05:53 PM

Tested quality
 
:cool:Thank You

v8volvo 05-05-2013 09:33 PM

Odd, What is making the noise? I changed almost everything in the front end when I put that together just about a year ago. New struts, mounts, balljoints, tie rod ends I think, cone bushings. You are sure the leak is from the strut tube?

RedArrow 05-30-2013 09:02 PM

Strut tube
 
3 Attachment(s)
Quote:

Originally Posted by ngoma (Post 6887)

The spring compressor worked fine!
I recently ordered Bilstein Touring inserts but I could not wait for it to arrive so I took the strut apart yesterday. Now I know for sure that the leak is from the strut tube...
The upper strut mount&the bearing is in good condition but the gland nut is pretty `old looking`& very rusty. The threads on it look so-so but not 100% great... I had too much clunking/knocking noises for a long time because it somehow became loose. I`m sure it did because last time while I was tightening `it shot itself up`and completely came out of the housing (making it harder* to remove the strut assembly). Threads of housing do not show major wear or damage. That`s the good news but I have to do the job again when new inserts arrive. Temporarily I put the thing back together. I noticed that the gland nut does screw in ALL THE WAY into the strut housing nicely and it looks/feels safe&tight. (threads ok? :) )
I really do not like to see half of the thread being out of the housing so I tried this. Especially because I know that it came apart by itself once already.

I decided to have it secured all the way into the housing BUT now I have to deal with something: it resulted me an issue that I could not solve right away and I`m asking your opinion on this matter.

There`s a removable spacer under (or IN?) the strut housing tube. I can`t get it back into its position (i think) because of the gland nut being secured all the way in the housing....so now I can`t safely connect the strut with the ball joint... there`s a 5-6 mm gap in between them! (strut tube lower end --- ball joint).

Any idea on what is the spacer really for and how/where to position it? Is it important to have it there or not? I tried to fit it both ways (regular and upside down too) but I just can`t make it fit or if I do, the ball joint can`t be tightly connected which I do not like. Something is wrong for sure (-with me) :) but i`ll redo both struts anyways. When I had the strut in parts, I just found the spacer on the ground (fell off) so Im not sure how it is positioned. Kill me for this stupid question but IS IT SUPPOSED TO BE *IN* the tube? :) I`m worse than lazy to remove&see the other strut just to figure this out (because I will have to do it soon anyways).

I am wondering that the `spacer` being out it should give me a lot more gland nut thread engagement... And I would really like that gland nut all the way in! When the new shocks come, I would do the same on the right side as well. Currently half of thread is visible (=out) there too. I feel better if this works out well. Great idea or a big no-no?
PS. Now I have the gland nut all the way in but a gap between the ball joints and the strut housing. If removing the spacer is NOt a great idea, shall I just go ahead and loosen my worn/dangerous gland nut back to gain the 5-6mm back for the spacer to fit in nicely? I`m sorry for thinking loud about it. Please comment.

745 TurboGreasel 05-31-2013 03:08 AM

Ball joint on first.
Spacer in the bottom of the tube (not all cartridge/strut combos need it)
install cartridge
the Gland nut must clamp the top shoulder of the cartridge against the bottom of the housing, it MUST NOT bottom on its threads. If it's threaded tight, and the cartridge can move at all, you needed the spacer.


All times are GMT -8. The time now is 01:55 AM.

Powered by vBulletin® Version 3.8.10
Copyright ©2000 - 2024, vBulletin Solutions, Inc.