PDA

View Full Version : ARP head studs


T-brick
05-29-2010, 05:11 PM
I got my sweet new ARP head studs today 190$ dollars later and they look sweet! now i need to get my steel head gasket any one no where to get one or have a part # for one?

hvguy
05-29-2010, 06:49 PM
I got my sweet new ARP head studs today 190$ dollars later and they look sweet! now i need to get my steel head gasket any one no where to get one or have a part # for one?

the dealer... i asked jason about it and he said he doesnt know anyone else that sells it =(

I read something somewhere that you have to have the right hole gasket... like a 2,3,4,5 hole gasket X_X not sure what this means, he said there are a certain number of holes in the front of the gasket... im sure this is an indication of the gasket thickness so that the pistons dont crush the valves =) "untill the timing belt breaks of course"

hvguy
05-29-2010, 06:50 PM
btw, whats the part number on those puppies?

Jason
05-30-2010, 06:16 AM
You can hold plenty of boost with the stock fiber gasket and studs. Guys have held 40psi with a 3notch head gasket and studs consistantly. The MLS gaskets are expensive through the dealer and hard to get it seams. I would just stick the fiber one in, just make sure you get a German one like Elring. If you have a 2 notch which is most likely, you can hold even more boost. Unless you have a built pump, I doubt you will be able to push much more than 35-40 psi anyway with a correctly sized turbo and the pump maxed out.

Did you buy them direct from ARP or what?

Jason

T-brick
05-30-2010, 09:18 AM
The part # for the ARP studs nuts and washers are AU5.400-1lub(studs)AUN12-2(nuts)AUW875N(washers) i got them direct from ARP

bjs2oo7
05-30-2010, 09:35 AM
http://alldatapro.com/alldata/PRO~V166548498~C12225~R0~OB0~P3R0H~N/0/34870059/56621793/56621796/56621802/34853741/100411974/34853743/34872038/34850961/120917497/56631191/41785455

bjs2oo7
05-30-2010, 09:40 AM
http://www.trademotion.com/partlocator/index.cfm?siteid=213668
Pictured above is the steel head gasket, click this link type in the part no. its about $70

T-brick
05-31-2010, 06:38 AM
I don't know what the part number is though?

bjs2oo7
05-31-2010, 08:15 AM
There was a picture in that blank post of minehttp://alldatapro.com/alldata/PRO~V166567170~C12225~R0~OB0~P3R0H~N/0/34870059/56621793/56621796/56621802/34853741/100411974/34853743/34872038/34850961/120917497/56631191/41785455

bjs2oo7
05-31-2010, 08:21 AM
In case that picture disappears again:
(Piston height above surface of cylinder head, number of holes, thickness, P/N)
0.67-0.80mm, 1 hole, 1.50mm, 91460071;
0.81-0.90mm, 2 holes, 1.55mm, 91460089;
0.91-1.02mm, 3 holes, 1.60mm, 91460097

T-brick
05-31-2010, 03:58 PM
Ok! cool thanks!!!;)

Jason
05-31-2010, 04:18 PM
I called them, their site says shows it, but it is on "intergalactic backorder" Seriously, those are the exact words of the guy I talked to. A couple months ago, they had one left.

Jason

hvguy
06-22-2010, 12:43 PM
I called them, their site says shows it, but it is on "intergalactic backorder" Seriously, those are the exact words of the guy I talked to. A couple months ago, they had one left.

Jason

when I talked to volvo back in... early may, they could only get 1,

maybe they checked the same place.....