Time to pump you up. (Injection pumps for sale)

[anders]

I have several injection pumps for sale.

Most pumps are now sold or being used as cores to build 12mm super pumps.

[anders]

Rebuilt d24t injection pump (by volvo) it may also be new. I ran it on my car for 1500 miles before I installed my turned up pump and then sold the car.
$820 shipped in the US.

[anders]

Looks to be a rebuilt pump or low mile original. I haven't ran this one myself but was told it was good. $320 shipped in the US

[anders]

Good injection pump, personal ran this one on my 86 744. $320 shipped in the US.

[anders]

This one was pulled from a 85 d24t that had low compression. $220 shipped

[anders]

This one was from a 1985 744, not sure on condition. I was told it was good when I acquired it back in 2010. $220 shipped in the US.

[anders]

This one was pulled from a rebuilt d24, pump was also rebuilt. I ran this one on the stand. $320 shipped in the US.

[anders]

This one was pulled from a running 244, I drove this car and it ran good. Pump looks to be rebuilt. $320 shipped in the US.

[anders]

This one was removed from a 1980 244, I was told it was good but couldn't verify because the engine had such low compression I couldn't get it started. $170 shipped in the US.

[anders]

I'm not sure where this one came from. $170 shipped in the US.

[RedArrow]

Excuse me for cluttering up your nice `pump-thread`. While looking at your picts I was wondering how nice it would be to put one of them into good use as a vw injector pop-tester but then I realized they are good pumps with a price-tag,LOL. No adapters would be needed, straight plug&play when d24 (or Rabbit?) hard line connected...


Looks like I cant find the freaking source online where I could buy/order the banjo fitting that is located at the OUT bolt on the inj pump (D24 `84 non-turbo)

It is a `dual` nipple it needs, I believe. I do have the OUT bolt itself and both copper washers.
The bolt measures 12mm diameter and it has that small hole on it plus a `miniature filter` inside which I must clean too.

Idk if it matters, but... (these Bosch VE pumps probably all use the same out-bolts...) this pump that i have the banjo missing from, looks to be an automatic car`s pump, it has the shutoff lever that i didn`t see on manual cars.

If you could sell me one that would be cool but a website link is also appreciated. I could Pm you with my address if mailing it isn`t a problem. Thank you

Something like this one
http://www.ebay.com/itm/130211483659?_trksid=p2055119.m1438.l2648&ssPageName=STRK%3AMEBIDX%3AIT
BUT it should have a 2nd nipple at a 90 or 180 degree angle.
I would say one is for a 6mm ID hose; the other one is probably appr 4mm OD but not sure and the 740 isn`t near me to check.

[ngoma]

I was wondering how nice it would be to put one of them into good use as a vw injector pop-tester...
What?

Looks like I cant find the freaking source online where I could buy/order the banjo fitting that is located at the OUT bolt on the inj pump (D24 `84 non-turbo)
If you can't find it online, try your local Bosch service center, they can look up the parts from your IP's model number embossed in its side.

[RedArrow]

What?


https://youtu.be/dIqTXoME54I
Well I watch rethink try do invent use say little weird things and when i saw this i loved the idea itself anyways. Isnt it a funky crap,dont you think??:)
I would possibly try this with an electric backup too (starter) idk why he didnt use all possible hardlines and injectors connected... That d be a nice display haha. A new pop pressure tester is def efficient/useful but not as creative as this diy junk.


If you can't find it online, try your local Bosch service center, they can look up the parts from your IP's model number embossed in its side.

I was searching it but nothing similar came up yet.
A bosch dealer? Nooo, this is nyc you need at least two hrs to get from a to b...no matter you walk drive or bike or travel by subway or a jet...i d prefer ordering it if someone knows where from. Or buy it used if available.

[fathead431]

still got any of the d24t pumps for sale?

[anders]

Most of the pumps have been built into 12mm super pumps and sold, the few remaining will most likely end up as super pumps too, or at least parts donors :-).